Welcome back to Sewing 201! This is where we talk about sewing tricks and techniques to take you beyond the basics. In this post I am going to pick up working on Chloe's little birthday dress. We left off after putting on the woven fabric neckline and armhole binding. Now all I have is the invisible zipper and the hem.
Why an invisible zipper? I just had this conversation with my sister and I'm going to share with you what I said. I have pulled my hair out in the past trying to make that lapped zipper approach look good. Just when I think it's in straight and I'm doing good, I ruin it when I go to topstitch it. I know that lots of people can do it and might even enjoy doing it that way. But finding invisible zippers was a revelation to me. There's no topstitching! If you can find that magic spot to sew not too close to the zipper teeth, but just close enough, then the zipper simply disappears into the fabric and your work is done. I love it. I sew invisible zippers into all of my dresses, tops, and skirts whether that's what the pattern calls for or not.
And I think my method is similar to the one in the package instructions, but I can't make heads or tails of those instructions so it's hard to say. I eventually started buying invisible zippers at Wawak.com because they're around 50 cents each and those don't come with instructions so it doesn't matter anyway.
For this method, we will put in the zipper before we sew the seam that it goes in. So the entire back seam of this dress is unsewn.
Finish the edges with a serger or zig zag stitch.
Since the neckline of my dress is already sewn and I won't be putting in a facing or lining, I trimmed away some extra tape from the top of my zipper. I used pinking shears so no one will be the wiser.
Turn your iron to the wool (medium) setting. You will notice that the zipper teeth on an invisible zipper naturally roll back toward the tape. While you roll them out to make the zipper tape flat, run your iron gently down the tape. Don't leave your iron in any one spot too long or you'll melt the teeth. This is just a preparatory step but it does help.
Pin the zipper to the left side of the dress with the right side of the zipper tape against the right side of the dress, as shown.
The outside edge of the zipper tape and your finished edge should line up.
Now look closely at the back of the zipper. There is a little line that shows you where to sew even though it seems like they try to hide it. It is about 1/8'' away from the teeth. On this zipper it is where the cross-weave texture of the zipper teeth ends. If you can't see the line, plan to sew about 1/8'' away from the teeth.
If you have an invisible zipper for your sewing machine that might make things easier for you. To be honest, I bought that plastic invisible zipper foot that they sell by the zippers and found it to be a waste of time and effort. So I just use my regular old zipper foot. I know that they do sell higher quality invisible zipper feet than the one I tried, so I might try again sometime. The idea behind them is that they have a little groove that the zipper teeth slide under. Obviously you don't need one because here I am sewing an invisible zipper in without it.
So go ahead and sew right down that zipper about 1/8'' away from the teeth or along the line that you might be able to see.
When your foot crashes into the zipper pull just backstitch and you're done. You don't have to bother trying to get around it.
Close the zipper and working from the inside of your item, pin the opposite zipper tape to the other side of the dress or skirt. Make sure the top edge lines up evenly.
Switch your needle or your zipper foot to the other side (however your sewing machine works) and sew down the other side of the zipper in exactly the same manner. As before, stop when you get to the zipper pull.
Zipper done! Now for that seam... pin the seam together. Remember how you finished your edge before you began? Doesn't that look nice now/
I still have my zipper foot on because it makes this part easier. Move the ends of the zipper tape out of your way and start sewing as close to where you stopped as possible. Stitch to the end and that's it!
I also tacked my zipper tape to the binding with a few stitches at the top for a finishing touch.
Do you have ideas for future Sewing 201 posts? Let me know below.